Also, keep in mind that once the transmission is removed and lowered to the floor, the vehicle must be high enough off the floor to allow the transmission to be slid out from underneath the vehicle.ĥ) DRAIN TRANSMISSION FLUID: Remove all the pan bolts except for a few bolts at one end of the pan – only loosen these. Note: When jacking up the vehicle, be sure to give yourself ample room to work underneath. Although it is not absolutely necessary, lifting the rear of the vehicle and supporting with jack stands makes the job a little easier. Using a floor jack, lift the front of the vehicle and secure with jack stands. Place a wheel chock or wooden block behind one of the rear wheels. Taking photos before disconnecting brackets, hoses and cables should serve the same purpose, which is to make the installation of these components easier and quicker.Ĥ) CHOCK REAR WHEEL – RAISE FRONT OF VEHICLE When disconnecting hoses and cables, make a drawing showing how each one is routed. Note: When removing brackets, mark their locations or make a simple drawing showing their locations. Note: You should be placing nuts and bolts in their labeled containers as you remove them. Remove any of the top bell housing to engine bolts that are accessible – otherwise the bolts will be removed later from underneath. Use a wire or strong bungee cord to hold the starter’s weight – do not hang from the starter wiring.ģ-C) Look closely at the top rear of the engine (back by the firewall) where the transmission bell housing bolts to the engine. Once the bolts are removed, just pull the starter out of the bell housing and push aside. Complete removal of the starter is normally not necessary. Any starter bolts that are not removed now will be removed later from underneath. Remove any starter bolts that are accessible. Still working under the hood, locate and disconnect any transmission electrical connectors you see.ģ-A) Remove any brackets, cables or hoses that connect the transmission to the engine.ģ-B) Now, locate the starter motor.
If not, you can remove it later from underneath. If you can see this nut/bolt and it is easily accessible, go ahead and remove it along with dipstick tube now. The dipstick tube (also called transmission fill tube) is normally secured to the transmission or engine with a single nut or bolt. Have your vehicle identification number (VIN) readily available before making the call.Ģ-A) On some vehicles, it may be necessary to remove the black plastic air intake components to give your sufficient space to work.Ģ-B) Now, locate the transmission fluid dipstick – pull it out and set it aside.
#2005 chevy cobalt transmission dipstick manual#
Check your Vehicle Owner’s Manual for the code or contact the service department of any auto dealership that sells your make vehicle for assistance. Note About Radio Code: On many newer vehicles, whenever the battery is disconnected a radio code is needed to get the stereo working again. Safety Tip: To eliminate any chance of battery arching, after removing the battery cable, wrap a rag around the cable end and place a wrap over the battery terminal. Move the cable end away from the battery post. Park your vehicle on a flat concrete surface, put the shifter in Park, set the emergency brake, pull the hood latch and then open the hood.ġ) Remove the negative battery cable. Note: Depending on your vehicle, additional labeled containers may be needed. > Torque Converter to Flywheel Bolts (or Nuts) > Exhaust and Exhaust Heat Shield Bolts/Nuts > Transmission Oil Cooler Line Fitting Washers
> Transmission Oil Fill/Dipstick Tube Bracket Bolt or Nut It’s best to get all the containers or baggies labeled before starting the job.įor removing the transmission from a rear wheel drive vehicle, you will need the following labeled containers/baggies. Organize nuts and bolts: For organizing nuts and bolts, we recommend using labeled plastic containers or baggies, whichever you have available. organized is important for two reasons… 1) it will save you time and frustration when re-installing the transmission and 2) it will insure all nuts and bolts are replaced in their original locations. Trending Questions Why motor smoke Ford Focus 2.0 1999? What is the labor cost to replace a fuel pump on a 1999 Mazda B4000 truck? How many gallons does a 2005 Lincoln Navigator hold? P0440 on 2000 Sunfire? How do you reset the fuel pump button on a 2000 dodge caravan? How do i change the fuel pump in an 1987 camaro? What causes 5.Keeping nuts, bolts, washers, clamps, etc.
0 kommentar(er)
